Hardware overview (IFP33)

Welcome to ViewBoard and your newly acquired interactive flat panel (IFP). Your ViewBoard IFP33 series comes with various components to assist in connecting devices and enhance your usage of the ViewBoard.

This article introduces the basics of the IFP33's additional hardware, as well as gives an overview of the display's control panel and ports.

Equipment basics

The following items are included in your IFP33's packaging:

What comes with your ViewBoard

  • Power cord (3m)
  • Remote control
  • AAA batteries
  • USB touch cable (3m)
  • Touch pen x2 (VP-PEN-009)
  • Quick Start Guide
  • Compliance Statement
  • RS-232 adapter
  • Clamp x5
  • Camera plate
  • Screw x8
  • HDMI cable (3m)
Delete

Wall mount kit specifications (VESA specs)

The following are some specifications for wall mounting an IFP33. For specific wall mount or mobile mount bracket installation steps, please review your IFP33's Quick Start Guide wall mount installation guide. If attaching to other building materials, please contact your nearest dealer.

6533

Rear panel with VESA spec measurements highlighted. Refer to the table below for corresponding measurements.

Delete

7533

Rear panel with VESA spec measurements highlighted. Refer to the table below for corresponding measurements.

Delete

8633

Rear panel with VESA spec measurements highlighted. Refer to the table below for corresponding measurements.

Delete

Model

VESA Spec.
(A x B)

Standard Screw 
(C x D)

Quantity

IFP6533 600 x 200 mm M8 x 25 mm 4
IFP7533 800 x 400 mm M8 x 25 mm 4
IFP8633 800 x 600 mm M8 x 25 mm 4
Delete

WARNING

Do not use screws that are longer than the standard dimension listed above. Using alternative screws may cause damage to the inside of the panel.

IFP33 controls and ports overview

This section breaks down the details of different input/out (I/O) ports and controls located on the IFP33.

Front panel of the IFP33 with input/output (I/O) ports and control panel areas highlighted.

6533

Rear panel.

Delete

7533

Rear panel.

Delete

8633

Rear panel.

Delete

Control panel

The control panel and front input/output (I/O), found on the bottom-right corner of the front of the IFP33, contain basic commands for the device and USB ports.

Refer to the table below for function details.


Button/Port

Function

1 Power indicator
  • Press to turn the device ON.
  • Press again to turn display backlight OFF/ON.
  • Press and hold to turn the device OFF.
2 Remote control receiver Receives commands from the device's remote control.
3 Ambient Light Sensor Monitors a room's ambient light.
4 USB Type-C USB Type-C input; connect to a PC with a USB Type-C output.
5 HDMI 1
  • High-definition input.
  • Connect to a PC (or other device) with an HDMI output.
6 TOUCH 1
  • Touch signal output to an external PC.
  • Pairs with HDMI 1.
7 USB Type-A
  • USB Type-A port.
  • Connect USB devices such as hard disks, keyboard, mouse, etc.

Input/output panels

Your IFP33 comes with multiple input/output (I/O) panels. The ports on these panels provide different ways to connect external devices by cable.

Overview of I/O panels located on different parts of the device.


Port

Function

1 RS-232 Serial interface; used for mutual transfer of data between devices.
2 LAN
  • Standard RJ45 (10M/100M/1G) Internet connection interface.
  • For ViewBoard and slot-in PC input sources.
3 USB Type-A Connect USB devices such as a hard disk, keyboard, mouse, etc.
4 TOUCH 2
  • Touch signal output to an external PC.
  • Pairs with HDMI 2/3 or VGA.
5 HDMI 2/3
  • High-definition input.
  • Connect to a PC (or other device) with an HDMI output.
6 HDMI OUT Connect to devices to display content from your IFP33 to it.
7 SPDIF For transmitting digital audio signals.
8 AUDIO OUT Audio to an external speaker or sound system.
9 AUDIO IN External computer audio input.
10 VGA External computer video input.
11 Power switch Turn AC power supply ON/OFF.
12 AC IN AC power input.

Knowledge Base

Need additional help?

Check our other resources — we'll be happy to assist you.